Job in international EPC Contractor company as the Commissioning Instrument Supervisor at the AGPP Project. Main responsibility as the Commissioning Instrument Supervisor is managing activities which is under my responsibility, in compliance with the quality requirements, health/environmental/safety regulations, and following the stated procedures. Main duties: - Commissioning activities for Instrument Items & Packages and activities for the functional tests during commissioning stage. - Participation in site inspections related to handover subsystems from Construction to Pre-commissioning. - Check and prepare relevant Commissioning punch list. - Monitor and ensure the activities are carried out following the procedures and requirements. - Ensure all safety rules are followed in the field. - Supervise the works of vendors’ specialists and ensure their efficient utilization. - Support Vendors’ specialists in the execution of the job and coordinate their actions with the Commissioning supervisors. - Keep records of all activities performed in the logbook to monitor the progress achieved and apply necessary recovery actions. - Ensure, that all the activities are witnessed by the Client, prepare and sign off all relevant certificates and hand over to certification engineer.

Job in international EPC Contractor company as the E&I Project Engineer at the Nord Stream 2 Project. Main duties as the E&I Project Engineer are: - Follow up preparation of Method Statements and Job cards by sub-contractors. Verify they are prepared in accordance with Project requirements and Russian Rules and Regulations; - Review and analyze drawings, technical reports, specification and other relevant Project documentation in order to identify changes comparing to Contract agreed scope of work; - Perform technical assessment of E&I equipment being supplied by Sub contractors; - Review of Subcontractor’s procedures, Method statements, Job cards; - Follow-up Sub Contractor’s permanent and temporary installation works; - Inspections of completed works, incoming control in accordance with subcontractor’s RFI; - Preparation of input required for Scope and Change Control department; - Preparation of Technical Queries and Concession Requests as required; - Participation in HSE activities, preparation of Risk Assessment and JSA for necessary works.

Job in international EPC Contractor company as a Commissioning Instrument Supervisor at the Yamal LNG project. Main tasks - loop check and troubleshooting of Instrumentation equipment on LNG trains. South Tambey LNG is a consolidated company of Technip (France), Chiyoda (Japan), and JGC (Japan). Commissioning and troubleshooting of all Instrumentation equipment for General Electric compressors (propane and mixed refrigerant), GE gas turbine and all miscellaneous equipment (cooling water system, washing water system for turbine, fire and gas system, fire suppression system, lube oil and hydraulic oil system, fuel gas, vibration sensors, HVAC, etc.). Specific responsibilities and duties: 1) Arrangement and managing of working process of subcontractors. Directly managing a team of 8-20 peoples (engineers and technicians) for loop check and troubleshooting of instrumentation equipment; 2) Ensuring that work is performed as per approved ITP/method statements/working procedures, applicable codes and standard; 3) Preparation of executive reports, progress reporting, and interfacing with client representatives, planning of loop check activities; 4) Checking of quality of all subcontractors activities; 5) Ensuring that all work is carried out to Project HSE requirements; 6) Directly participate to the all HSE activities in area of my responsibility; 7) Assistance and managing vendor specialists. 8) Work with punch list (creation and closure of punches); Achievements: • Received experience with Instrumentation of General Electric compressors for propane and mixed refrigerant (Model MCL1405, BCL806 & 3MCL1404), gas turbines (Model MS7001 EA DLN) with all miscellaneous equipment (cooling water system, washing water system for turbine, fire and gas system, fire suppression system, lube oil and hydraulic oil system, fuel gas, vibration sensors, HVAC, etc.). • Position in an international company (EPC contractor) in multinational collective; • Fluent English (good speaking and writing skills); • Experience in using EASYPLANT and EDMS software.

Successfully finished Yamal LNG Tanks project. Job at position of Electrical and Instrumentation supervisor in EPC Contractor company of Yamal LNG Tanks project. Construction and commissioning of 4 LNG tanks. Main responsibility is all the works on construction site, concerning Electrical or Instrumentation activities. Commissioning of electrical equipment (Heat tracing system, winterization system, lighting and small power, etc.). Megger tests of cables, testing of MCCB, RCCD. Commissioning of Instrumentation equipment (Tank Gauging System). Specific responsibilities and duties: 1) Arrangement and managing of working process of all E&I Subcontractors. Directly managing a team of 50-100 subcontractor’s peoples (engineers, technicians, fitters, etc.). 2) Supervision of installation for the next low voltage equipment (230, 400 V): cable trays; pulling of cables; installation and connection of junction boxes, distribution panels, heaters, lighting equipment, lightning protection, earthing; installation and connection of heat tracing cables, heat tracing junction boxes and distribution panels. 3) Supervision of installation for the next medium voltage equipment (6000 V): Cable trays. 4) Supervision of installation for the next instrumentation equipment: Cable trays for instrumentation cables; Pulling of instrumentation cables; installation and connection of junction boxes, temperature elements and transmitters, pressure and differential pressure transmitters, level transmitters, fire and gas detectors, heating boxes for equipment, earthing of instrumentation equipment; 5) Ensuring that work is performed as per approved ITP/method statements/working procedures, applicable codes and standards; 6) Checking of quality of all subcontractors activities; 7) Ensuring that all work is carried out to Project HSE requirements; 8) Directly participate to the all HSE activities at site; 9) Detection of any design errors, and where possible to rectify or request to the E&I Manager to make the necessary changes; 10) Checking Subcontractors’ work progress status sheets and sign the same for approval; 11) Assist and manage vendor specialists. Achievements: • Received experience in construction and installation of equipment with special requirements for LNG site; • Job in an international company (EPC contractor) • Fluent English (good speaking and writing skills);

Maintenance and repair of instrumentation equipment for shore tank farm Varandey oil export terminal PJSC "LUKOIL". Worked with the following equipment: 1) Rosemount 5600 Radar Level Transmitter , SAAB Tank Radar, Rosemount 2120 Vibrating Fork Liquid Level Switch, Rosemount 3300 Wave Radar Level and Interface Transmitter. 2) Drager gas concentration monitoring systems 3) Automatic valves with actuators Rotork, AUMA 4) Pressure transmitters Endress Hauser, Rosemount 5) Temperature transmitters Rosemount, Honeywell 6) Flowmeters 7) DeltaV Distributed Control System Work as an operational duty engineer. Achievements: Acquisition of experience in preventive maintenance of control and instrumentation equipment.

Assign tasks to employees, monitoring assignments, report to the Head of Process Control System group (Project director) Supervision of the installation and commissioning works, conducting the documentation, preparation of executive documentation (sections P&I), signing of the acceptance documentation (Turnover documentation) Participation in the design of objects as a technical expert, review and checking design for compliance with the current regulatory documents. Participation in the selection of equipment at the design stage, working with equipment suppliers from drawing up a request to harmonize procurement and shipment of equipment. Setting up and commissioning systems of emergency protection (ESD), gas concentration monitoring systems, security systems and fire alarms, CCTV system and access control systems for the oil and gas industry facilities. Connecting and setting up equipment based on PLC Siemens, Allen Bradley. Experienced with equipment of manufacturers such as Elemer, Metran, Rosemount, Siemens, General Monitors, Electronstandart-pribor. Experienced in the installation and commissioning of variable frequency drives Vacon, Lenze, Siemens. The main objects was a gas compressor stations on the basis of Ariel compressors. Also have an experience in construction of energy center at the base of the generators with gas engines Waukesha. The main functions and responsibilities: Managing of execution of works, checking the compliance of performed work for customer requirements and regulatory documents. The interaction with the customer as part of work performed. Managing of engineering and technical personnel, managing of workers (issuing assignments, monitoring). Participation in the design of objects as a technical expert. Received an experience in the management of personnel, knowledge of regulatory documents, experience in working with foreign specialists.

Setting up and commissioning systems of emergency protection (ESD), gas concentration monitoring systems, security systems and fire alarms, CCTV system and access control systems for the oil and gas industry facilities. Connecting and setting up equipment based on PLC Siemens, Allen Bradley. Experienced with equipment of manufacturers such as Elemer, Metran, Rosemount, Siemens, General Monitors, Electronstandart-pribor. Experienced in the installation and commissioning of variable frequency drives Vacon, Lenze, Siemens. The main objects was a gas compressor stations on the basis of Ariel compressors. Also have an experience in construction of energy center at the base of the generators with gas engines Waukesha. The main functions and responsibilities: Participation in the selection of equipment at the design stage, working with equipment suppliers from drawing up a request to harmonize procurement and shipment of equipment. Participation in the installation and commissioning work, supervising the installation and commissioning, documentation, participation in the acceptance tests, the preparation of executive documentation (sections P&I), the signing of the acceptance documentation. Acquired experience in commissioning of various equipment, knowledge of regulatory documents, experience in working with foreign specialists

Installation and adjustment of systems of fire alarm systems, CCTV and access control systems, installation and connection of instrumentation equipment. Managing a team of fitters. Acquired experience in connecting various domestic and foreign equipment

Repair of oilfield mechanical equipment